PLUMBING BASICS: WHAT YOU NEED FOR BATHTUB INSTALLATION

Plumbing Basics: What You Need for Bathtub Installation

Plumbing Basics: What You Need for Bathtub Installation

Blog Article

Click Here

Are you currently interested in advise on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Installing a bath tub isn't precisely rocket science, however it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is easily easily accessible, the job can relocate rapidly; if you have to open a wall surface to eliminate the old tub and also position the brand-new tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub as well as embeded in the brand-new one. Ensure you have qualified on your own for the work and also fit attempting it. Rather than employing a service provider to take over a halfway-completed job, it is far better to think about utilizing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly help you install a brand-new bathtub in your bathroom if you have already purchased a new bathtub and also don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited accessibility that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. Once the supply pipelines have been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
    Prior to proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines are in place in between the tap and also the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind must be connected to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.

    Setting up the Tub


    Making use of the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
    The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub till the spirit level reviews level.
    To mount faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
    Turn on the water as well as inspect all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the tub and also check the overflow electrical outlet as well as the typical outlet for leaks.
    Lastly, fix the bath paneling as described in the maker's instruction manual. Tiling and also securing around the tub should wait till the bathtub has actually been utilized at the very least once as this will certainly settle it into its last position.

    Getting ready for the Installation


    First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to avoid stress on the tub.
    Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
    Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom and also the tiling, causing issues with dampness and also possible leaks to the ceiling listed below.
    You can select from a selection of coloured sealants to blend in your components as well as installations. They are sold in tubes as well as cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to enable the activity experienced when the bathtub is in use. The sealant can fracture rather very early if you do not take into account this movement prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you really like more info about How to Install a Bathtub Yourself? Try to leave a comment below. We would be delighted to know your thinking about this content. We are looking forward that you visit us again before long. Sharing is caring. Who knows, you could be doing someone a favor. Thank-you for your time spent reading it.


    Reliable help? Dial.

    Report this page